sw1tch
14-09-2006, 05:55 AM
bueno inaguro hehehe con un par de problemas :(
el tema es que estoy por vender mis memos ocz gold 2x512 OCZ OCZ5001024ELDCGEVX
la onda es que las habia subido un amigo junto con el procesador
un opteron 148 a los 2.75 estables....
El tema es que me voy a comprar una tccd y tengo que bajar las memos y estuve por dfi street y sinceramente ya la cabeza no me da mas....
puse todo en stock y solo me toma una memoria en vez de las dos (con el voltaje stock)
vagueando por inet encontre un usuario con un problema similar a lo que le respondieron que ponga primero la memo que funciona en el slot naranja (es un dfi ultra d nf4) despues darle en el dram voltage = 3.0v activar el mem86 despues ponerle los timings 2-3-2-8 apenas salvo y resetea , la apago y pongo la segunda memo (la que me da problemas) en el segundo slot naranja mas cerca al cpu) la memoria la tomo y tiraba errores en el memtest86 (nose si sea bueno o malo) cuestion reseteo y funcionaba lo mas bien pero el voltaje me quedo tal cual lo puse. (3.12v)
aca esta lo que le respondieron
Try the following and see:
Do you have 1 stick of ram that appears "Bad"...meaning it won't boot the board if you clear CMOS? If so, then please try the procedure outlined below. This will help us determine if the ram itself is bad.
This procedure should apply to Any bios that you might be using but I have only tested it on 310, 326, 414-2, and 510-2.
If this does not solve your problems, please create yourself a thread so that we can help you individually.
1) Clear the CMOS on the board.
2) Place your "good" stick in slot 2 (farthest orange from CPU)
3) Boot up the board and get into the bios.
4) On the Genie Bios page, set the DRAM Voltage to 3.0V.
5) Enable Memtest86+ on the Genie Bios page.
6) On the DRAM Config page, set the 4 main timings to 2-3-2-8 (CAS-tRCD-tRP-tRAS) (2-3-8-2 top to bottom in the bios).
7) Choose "Save and Exit" answer yes and let the board reboot.
8) Once you see memtest, power down the board.
9) Insert the "Bad" stick into slot 4 (closest orange to CPU)
10) Now power up the board, you should get to memtest.
If you get to memtest, then your memory is fine and does not need to be RMA'd
Despues se me ocurrio la idea de poner que ya tenia guardado a cuanto lo habiamos subido lo cual no recordaba y me tiro estas specs
CPU Type AMD Opteron 148
CPU Alias Venus S939
CPU Stepping SH-E4
CPUID CPU Name AMD Opteron(tm) Processor 148
CPUID Revision 00020F71h
CPU Speed
CPU Clock 2750.8 MHz (original: 2200 MHz, overclock: 25%)
CPU Multiplier 11.0x
CPU FSB 250.1 MHz (original: 200 MHz, overclock: 25%)
Memory Bus 250.1 MHz
DRAM:FSB Ratio CPU/11
CPU Cache
L1 Code Cache 64 KB (Parity)
L1 Data Cache 64 KB (ECC)
L2 Cache 1 MB (On-Die, ECC, Full-Speed)
Motherboard Properties
Motherboard ID 07/02/2005-NF-CK804-6A61FD49C-00
Motherboard Name DFI nF4 Series
Chipset Properties
Motherboard Chipset nVIDIA nForce4, AMD Hammer
Memory Timings 2-3-3-8 (CL-RCD-RP-RAS)
Command Rate (CR) 1T
SPD Memory Modules
DIMM3: OCZ OCZ5001024ELDCGEVX 512 MB PC4000 DDR SDRAM (2.5-4-4-8 @ 250 MHz)
DIMM4: OCZ OCZ5001024ELDCGEVX 512 MB PC4000 DDR SDRAM (2.5-4-4-8 @ 250 MHz)
BIOS Properties
System BIOS Date 07/02/05
Video BIOS Date 09/23/05
Award BIOS Type Phoenix - Award WorkstationBIOS v6.00PG
Award BIOS Message (N4D702-2) EVALUATION ROM - NOT FOR SALE
DMI BIOS Version 6.00 PG
Graphics Processor Properties
Video Adapter ATI Radeon X1800 XL (R520)
GPU Code Name R520 (PCI Express x16 1002 / 7109, Rev 00)
GPU Clock 500 MHz (original: 500 MHz)
Memory Clock 495 MHz (original: 495 MHz)
http://img81.imageshack.us/img81/4562/3tv7.th.jpg (http://img81.imageshack.us/my.php?image=3tv7.jpg)
Ahora estoy con solo un modulo de 512 y todo stock y el everest tira:
CPU Type AMD Opteron 148
CPU Alias Venus S939
CPU Stepping SH-E4
CPUID CPU Name AMD Opteron(tm) Processor 148
CPUID Revision 00020F71h
CPU Speed
CPU Clock 2210.2 MHz (original: 2200 MHz)
CPU Multiplier 11.0x
CPU FSB 200.9 MHz (original: 200 MHz)
Memory Bus 200.9 MHz
DRAM:FSB Ratio CPU/11
CPU Cache
L1 Code Cache 64 KB (Parity)
L1 Data Cache 64 KB (ECC)
L2 Cache 1 MB (On-Die, ECC, Full-Speed)
Motherboard Properties
Motherboard ID 07/02/2005-NF-CK804-6A61FD49C-00
Motherboard Name DFI nF4 Series
Chipset Properties
Motherboard Chipset nVIDIA nForce4, AMD Hammer
Memory Timings 2.5-3-3-7 (CL-RCD-RP-RAS)
Command Rate (CR) 1T
SPD Memory Modules
DIMM3: OCZ OCZ5001024ELDCGEVX 512 MB PC4000 DDR SDRAM (2.5-4-4-8 @ 250 MHz)
BIOS Properties
System BIOS Date 07/02/05
Video BIOS Date 09/23/05
Award BIOS Type Phoenix - Award WorkstationBIOS v6.00PG
Award BIOS Message (N4D702-2) EVALUATION ROM - NOT FOR SALE
DMI BIOS Version 6.00 PG
Graphics Processor Properties
Video Adapter ATI Radeon X1800 XL (R520)
GPU Code Name R520 (PCI Express x16 1002 / 7109, Rev 00)
GPU Clock 500 MHz (original: 500 MHz)
Memory Clock 495 MHz (original: 495 MHz)
==========
info de la memo sola que me tira el everest
Field Value
Memory Module Properties
Module Name OCZ OCZ5001024ELDCGEVX
Serial Number None
Module Size 512 MB (2 ranks, 4 banks)
Module Type Unbuffered
Memory Type DDR SDRAM
Memory Speed PC4000 (250 MHz)
Module Width 64 bit
Module Voltage SSTL 2.5
Error Detection Method None
Refresh Rate Reduced (7.8 us), Self-Refresh
Memory Timings
@ 250 MHz 2.5-4-4-8 (CL-RCD-RP-RAS)
Memory Module Features
Early RAS# Precharge Not Supported
Auto-Precharge Not Supported
Precharge All Not Supported
Write1/Read Burst Not Supported
Buffered Address/Control Inputs Not Supported
Registered Address/Control Inputs Not Supported
On-Card PLL (Clock) Not Supported
Buffered DQMB Inputs Not Supported
Registered DQMB Inputs Not Supported
Differential Clock Input Supported
Redundant Row Address Not Supported
una mano o consejo es agradecido
el tema es que estoy por vender mis memos ocz gold 2x512 OCZ OCZ5001024ELDCGEVX
la onda es que las habia subido un amigo junto con el procesador
un opteron 148 a los 2.75 estables....
El tema es que me voy a comprar una tccd y tengo que bajar las memos y estuve por dfi street y sinceramente ya la cabeza no me da mas....
puse todo en stock y solo me toma una memoria en vez de las dos (con el voltaje stock)
vagueando por inet encontre un usuario con un problema similar a lo que le respondieron que ponga primero la memo que funciona en el slot naranja (es un dfi ultra d nf4) despues darle en el dram voltage = 3.0v activar el mem86 despues ponerle los timings 2-3-2-8 apenas salvo y resetea , la apago y pongo la segunda memo (la que me da problemas) en el segundo slot naranja mas cerca al cpu) la memoria la tomo y tiraba errores en el memtest86 (nose si sea bueno o malo) cuestion reseteo y funcionaba lo mas bien pero el voltaje me quedo tal cual lo puse. (3.12v)
aca esta lo que le respondieron
Try the following and see:
Do you have 1 stick of ram that appears "Bad"...meaning it won't boot the board if you clear CMOS? If so, then please try the procedure outlined below. This will help us determine if the ram itself is bad.
This procedure should apply to Any bios that you might be using but I have only tested it on 310, 326, 414-2, and 510-2.
If this does not solve your problems, please create yourself a thread so that we can help you individually.
1) Clear the CMOS on the board.
2) Place your "good" stick in slot 2 (farthest orange from CPU)
3) Boot up the board and get into the bios.
4) On the Genie Bios page, set the DRAM Voltage to 3.0V.
5) Enable Memtest86+ on the Genie Bios page.
6) On the DRAM Config page, set the 4 main timings to 2-3-2-8 (CAS-tRCD-tRP-tRAS) (2-3-8-2 top to bottom in the bios).
7) Choose "Save and Exit" answer yes and let the board reboot.
8) Once you see memtest, power down the board.
9) Insert the "Bad" stick into slot 4 (closest orange to CPU)
10) Now power up the board, you should get to memtest.
If you get to memtest, then your memory is fine and does not need to be RMA'd
Despues se me ocurrio la idea de poner que ya tenia guardado a cuanto lo habiamos subido lo cual no recordaba y me tiro estas specs
CPU Type AMD Opteron 148
CPU Alias Venus S939
CPU Stepping SH-E4
CPUID CPU Name AMD Opteron(tm) Processor 148
CPUID Revision 00020F71h
CPU Speed
CPU Clock 2750.8 MHz (original: 2200 MHz, overclock: 25%)
CPU Multiplier 11.0x
CPU FSB 250.1 MHz (original: 200 MHz, overclock: 25%)
Memory Bus 250.1 MHz
DRAM:FSB Ratio CPU/11
CPU Cache
L1 Code Cache 64 KB (Parity)
L1 Data Cache 64 KB (ECC)
L2 Cache 1 MB (On-Die, ECC, Full-Speed)
Motherboard Properties
Motherboard ID 07/02/2005-NF-CK804-6A61FD49C-00
Motherboard Name DFI nF4 Series
Chipset Properties
Motherboard Chipset nVIDIA nForce4, AMD Hammer
Memory Timings 2-3-3-8 (CL-RCD-RP-RAS)
Command Rate (CR) 1T
SPD Memory Modules
DIMM3: OCZ OCZ5001024ELDCGEVX 512 MB PC4000 DDR SDRAM (2.5-4-4-8 @ 250 MHz)
DIMM4: OCZ OCZ5001024ELDCGEVX 512 MB PC4000 DDR SDRAM (2.5-4-4-8 @ 250 MHz)
BIOS Properties
System BIOS Date 07/02/05
Video BIOS Date 09/23/05
Award BIOS Type Phoenix - Award WorkstationBIOS v6.00PG
Award BIOS Message (N4D702-2) EVALUATION ROM - NOT FOR SALE
DMI BIOS Version 6.00 PG
Graphics Processor Properties
Video Adapter ATI Radeon X1800 XL (R520)
GPU Code Name R520 (PCI Express x16 1002 / 7109, Rev 00)
GPU Clock 500 MHz (original: 500 MHz)
Memory Clock 495 MHz (original: 495 MHz)
http://img81.imageshack.us/img81/4562/3tv7.th.jpg (http://img81.imageshack.us/my.php?image=3tv7.jpg)
Ahora estoy con solo un modulo de 512 y todo stock y el everest tira:
CPU Type AMD Opteron 148
CPU Alias Venus S939
CPU Stepping SH-E4
CPUID CPU Name AMD Opteron(tm) Processor 148
CPUID Revision 00020F71h
CPU Speed
CPU Clock 2210.2 MHz (original: 2200 MHz)
CPU Multiplier 11.0x
CPU FSB 200.9 MHz (original: 200 MHz)
Memory Bus 200.9 MHz
DRAM:FSB Ratio CPU/11
CPU Cache
L1 Code Cache 64 KB (Parity)
L1 Data Cache 64 KB (ECC)
L2 Cache 1 MB (On-Die, ECC, Full-Speed)
Motherboard Properties
Motherboard ID 07/02/2005-NF-CK804-6A61FD49C-00
Motherboard Name DFI nF4 Series
Chipset Properties
Motherboard Chipset nVIDIA nForce4, AMD Hammer
Memory Timings 2.5-3-3-7 (CL-RCD-RP-RAS)
Command Rate (CR) 1T
SPD Memory Modules
DIMM3: OCZ OCZ5001024ELDCGEVX 512 MB PC4000 DDR SDRAM (2.5-4-4-8 @ 250 MHz)
BIOS Properties
System BIOS Date 07/02/05
Video BIOS Date 09/23/05
Award BIOS Type Phoenix - Award WorkstationBIOS v6.00PG
Award BIOS Message (N4D702-2) EVALUATION ROM - NOT FOR SALE
DMI BIOS Version 6.00 PG
Graphics Processor Properties
Video Adapter ATI Radeon X1800 XL (R520)
GPU Code Name R520 (PCI Express x16 1002 / 7109, Rev 00)
GPU Clock 500 MHz (original: 500 MHz)
Memory Clock 495 MHz (original: 495 MHz)
==========
info de la memo sola que me tira el everest
Field Value
Memory Module Properties
Module Name OCZ OCZ5001024ELDCGEVX
Serial Number None
Module Size 512 MB (2 ranks, 4 banks)
Module Type Unbuffered
Memory Type DDR SDRAM
Memory Speed PC4000 (250 MHz)
Module Width 64 bit
Module Voltage SSTL 2.5
Error Detection Method None
Refresh Rate Reduced (7.8 us), Self-Refresh
Memory Timings
@ 250 MHz 2.5-4-4-8 (CL-RCD-RP-RAS)
Memory Module Features
Early RAS# Precharge Not Supported
Auto-Precharge Not Supported
Precharge All Not Supported
Write1/Read Burst Not Supported
Buffered Address/Control Inputs Not Supported
Registered Address/Control Inputs Not Supported
On-Card PLL (Clock) Not Supported
Buffered DQMB Inputs Not Supported
Registered DQMB Inputs Not Supported
Differential Clock Input Supported
Redundant Row Address Not Supported
una mano o consejo es agradecido